Teen Babes Videos - Fantasy Young Girls And Their First Fuck

[vipmodel]

Tiny Girl and Beautiful Teenagers Amateur Sex
526Mb 1920x1080 0:15:59 mp4





http://k2s.cc/file/c12d2a6b21d64/456367568679758903.mp4

[EQiblyGow]

<h2> Using the Balanset-1A Instrument </h2>

<h3> Getting the Equipment Ready </h3>
<ul>
<li> Ensure the instrument is complete with all necessary components: vibration transducers, laser tachometer, magnetic stand, software, and other accessories. </li>
<li> Connect the device to your PC using the USB interface and confirm the software installation. </li>
</ul>

<h3> Sensor Installation </h3>
<ul>
<li> Fix the accelerometers securely to the machine's structure in locations where vibrations are most prominent, ideally near the bearings. </li>
<li> Position the laser tachometer (phase angle sensor) so that it is aimed at the rotor. Attach reflective tape to the rotor for accurate phase angle reading. </li>
</ul>

<h3> Launching the Software </h3>
<ul>
<li> Launch the Balanset software on your computer. </li>
<li> Select the appropriate balancing mode: single-plane or two-plane, depending on the rotor type and your specific requirements. </li>
</ul>

<h3> </h3>
<a href="https://vibromera.eu/wp-content/uploads/2024/11/2-Camera_01.png" target="_blank">
<img src="https://vibromera.eu/wp-content/uploads/2024/11/2-Camera_01.png" alt="2-Camera_01" style="width: 50%; display: block; margin-bottom: 10px;">
</a>
<ul>
<li> Bring the rotor to its normal operating rotational frequency. </li>
<li> The application will acquire data on vibration magnitude, rotational velocity, and phase angle to determine the initial imbalance state. </li>
</ul>

<h3> Mounting the Test Weight </h3>
<a href="https://vibromera.eu/wp-content/uploads/2024/11/3-Camera-2_01.png" target="_blank">
<img src="https://vibromera.eu/wp-content/uploads/2024/11/3-Camera-2_01.png" alt="3-Camera-2_01" style="width: 50%; display: block; margin-bottom: 10px;">
</a>
<ul>
<li> Halt the rotation and mount a test weight at a designated position on the rotor, with the weight's value entered into the software (usually in grams). </li>
<li> Run the rotor again, allowing the software to measure the effects of the trial weight on vibration and phase. </li>
</ul>
<a href="https://vibromera.eu/wp-content/uploads/2024/11/5-Camera_01.png" target="_blank">
<img src="https://vibromera.eu/wp-content/uploads/2024/11/5-Camera_01.png" alt="5-Camera_01" style="width: 50%; display: block; margin-bottom: 10px;">
</a>


<h3> Determining the Corrective Mass </h3>
<ul>
<li> The software uses the measured values to automatically compute the necessary compensating weight's magnitude and placement angle. </li>
<li> These parameters are displayed on the screen as numerical data and graphs. </li>
</ul>
<a href="https://vibromera.eu/wp-content/uploads/2024/02/Bs1ManualEngV156-May2023-10448629.png" target="_blank">
<img src="https://vibromera.eu/wp-content/uploads/2024/02/Bs1ManualEngV156-May2023-10448629.png" alt="Bs1 Manual" style="width: 30%; display: block; margin-bottom: 10px;">
</a>

<h3> Attaching the Corrective Mass </h3>
<ul>
<li> Install the correction weight on the rotor according to the software's calculations. </li>
<li> You can conduct interim measurements to confirm that the imbalance is decreasing as expected. </li>
</ul>
<a href="https://vibromera.eu/wp-content/uploads/2024/11/1-Camera-2_01.png" target="_blank">
<img src="https://vibromera.eu/wp-content/uploads/2024/11/1-Camera-2_01.png" alt="1-Camera-2_01" style="width: 50%; display: block; margin-bottom: 10px;">
</a>

<h3> Final Check and Balance Confirmation </h3>
<ul>
<li> With the compensating weight attached, operate the rotor and assess the level of any residual vibration. </li>
<li> If the measured vibration falls within the tolerance defined by ISO 1940, the balancing process is considered successful. </li>
<li> If the vibration is still outside acceptable limits, reiterate the process and fine-tune the compensating weight. </li>
</ul>

<h3> Creating a Balancing Report </h3>
<ul>
<li> The balancing results are saved in the software's archive. You can create and print a report containing vibration data, correction weight mass, and its installation angle. </li>
</ul>

<h3> Concluding Steps and Verification </h3>
<ul>
<li> Verify the secure attachment of all balancing weights and measurement sensors. </li>
<li> Confirm that the rotor spins freely and quietly, without any unusual sounds or vibrations. </li>
<li> If the rotor operates within a larger assembly, check the functionality and interplay of all interconnected parts. </li>
</ul>

<p> Following this procedure enables accurate balancing, minimizes vibration, and prolongs the service life of the equipment. </p>




Instagram: https://www.instagram.com/vibromera_ou/
Youtube : https://youtu.be/guA6XJ-ArZM?si=vmkuX7RILzKBl0zL
Our website about <a href="https://vibromera.eu
"> Balancing of mill rotors in cement industry </a>
Machinio: https://www.machinio.com/listings/983801...n-portugal
Facebook: https://www.facebook.com/marketplace/ite...1228150722

http://www.pax.nichost.ru/forum/view_pro...UID=144082